Epoxy.com Product #115 "C"
Epoxy Modified Normal Set Concrete Pack
DESCRIPTION:
Epoxy.com Product #115 "C" Component Epoxy Modified Normal Set Concrete Pack
with corrosion inhibitor is produced with the use of 100% solids epoxy
resin, specifically formulated to be compatible with cement, water,
aggregate and sand mixtures. Epoxy.com Product #115 is easy to
mix and is placed like ordinary mortar or concrete. It is dark gray in
color.
ADVANTAGES:
- Prevents corrosion of steel.
- Prepackaged grout is ready to use.
- High compressive and tensile strengths.
- Low absorption with no shrinkage.
- Has excellent freeze-thaw and impact resistance properties
- Economical.
- Modulus of elasticity is the same as concrete.
WHERE TO USE:
Industrial floor overlays, parking garages, bridge decks, bridge seats,
sidewalks, pile and pier restoration where low absorption and high strength
is needed. To prevent deterioration of concrete and reinforcing steel. Rapid
transit track pads.
PHYSICAL PROPERTIES:
|
Working Time
|
Same as ordinary concrete
|
|
Color of mixed material
|
Dark Gray
|
|
Consistency after mixing
|
3" slump ±
|
|
Compressive Strength
ASTM C109
|
|
1 day
|
2200
|
|
|
3 days
|
6,000 psi
|
|
|
7 days
|
7,000 psi
|
|
|
14 days
|
9,000 psi
|
|
|
Tensile Strength (ASTM C-307)
|
|
1 day
|
85 psi
|
|
|
3 days
|
350 psi
|
|
|
7 days
|
465 psi
|
|
|
14 days
|
865 psi
|
|
|
28 days
|
945 psi
|
|
|
Flexural Strength
|
|
28 days
|
1500 psi
|
10.34 MPa
|
|
Water Absorption
ASTM C-413
|
1.28% |
|
|
Volume Change
ASTM C-827-78
|
0.44% |
|
SURFACE PREPARATION:
Substrate must be clean and sound. Apply Epoxy.com
Product #7 Bonding Agent to the surface to be repaired at
a rate of approximately 100 SF/gallon (2.45 m2/gal.). While the bonding
agent is still tacky, place the epoxy modified mortar or concrete mix or
apply a slurry coat of Epoxy Modified Mortar to the area to be repaired.
Place the epoxy modified mortar or concrete while the slurry is still wet.
MIXING:
Start mixer and place Epoxy.com Product #115 "C" Component into
mixer and add up to 3/4 gallons ( 2.84 liter) of water per bag; add 1 gallon
(3.785 liter) of mixed epoxy resin for each bag of C Component; mix for an
additional 3 to 5 minutes. Additional water may be added to produce desired
consistency (keep water content as low as possible).
Recommended Proportioning for Epoxy Modified Mortar
Epoxy.com Product #115 "C" Component 3 bags (60 lbs. each) — 27.2
kilos
Epoxy.com Product #115 Epoxy 3 gallons 11.36 liters
Water — 2-1/4 gallons (approx) — 8.5 liters
Approximate Yield — 1.55 cubic feet — 43.9 liters
Recommended Proportioning for Epoxy Modified Concrete Normal Set
Epoxy.com Product #115 "C" Component — 3 bags (60 lbs. each) — 27.2
kilos
3/8" pea gravel 90 lbs. — 40.8 kilos
Epoxy.com Product #115 Epoxy 3 gallons — 11.36 liters
Water — 2-1/4 gallons (approx) — 8.5 liters
Approximate Yield — 2.2 cubic feet — 62.3 liters
Place Coarse Aggregate in concrete mixer and start mixing. Add
Epoxy.com Product #115 "C" C Component, add water to produce desired
consistency, add mixed epoxy and mix an additional 3 to 5 minutes.
APPLICATION:
Place in conventional manner. Finishing may be improved with a vibrating
screed. After screeding, allow bleed water to come to the surface, finish
with steel trowel. Finishing may be aided by wiping trowel with solvent. Surface may be broomed.
Protect concrete during initial set with polyethylene sheeting. When
concrete is sufficiently hard, cure with both burlap and polyethylene
sheeting. Continue cure for 24 hours
CLEAN UP:
Flush equipment frequently with water. Tools in contact with neat epoxy
must be cleaned with
solvent-type cleaner. Tools in contact with concrete or mortar may be washed
with water.
LIMITATION:
Store material between 65° F (18.3° C) and 85° F (29.4° C) during mixing.
Do not mix Epoxy.com Product #115 "C" with organic solvents.
STORAGE:
Keep in cool, dry place.
SHELF LIFE:
Two years
CAUTION:
"A" COMPONENT - Contains Epoxy Resin. May cause skin sensitization or
other allergic responses. Avoid inhalation of vapor. Use good ventilation
particular if material is heated or sprayed. Prevent all contact with skin
or eyes. If contact with skin occurs, wash immediately with soap and water.
In case of contact with eyes, flush immediately with water and contact a
physician.
"B" COMPONENT - Contains alkaline amines, strong sensitizer. May cause
burns. Do not get into eyes, on skin, or clothing. Avoid breathing vapor.
Keep container closed. Use with adequate ventilation. Wash thoroughly after
handling.
"C" COMPONENT - Cement powder or freshly mixed concrete or mortar may
cause skin injury. Avoid contact with skin; wash exposed areas promptly with
water. If any cement powder or mixture gets into eyes, rinse immediately and
repeatedly with water. Get prompt medical attention!
FIRST AID:
In case of contact, immediately flush eyes or skin with plenty of water
for at least 15 minutes. Remove contaminated clothing and shoes. Call a
physician. Wash clothing before reuse. Discard contaminated shoes.
WEAR PROTECTIVE CLOTHING, GOGGLES, GLOVES AND/OR BARRIER CREAMS
FOR INDUSTRIAL USE ONLY. KEEP AWAY FROM CHILDREN.
Proper mixing and installation is critical to the optimal success of all
product. See Installation Tips,
Techdata, &
MSDS for more details on our products.
Be sure to contact us with any questions and/or concerns that you have.
For more information please contact:
Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over
375 products,
Since 1980
Florida & Vermont
USA
Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch.
321-206-1833 Customer Service - Ordering and Order Status
Katey Fontaine, VP - Customer Service Director
sales@epoxy.com
714-657-3826 Technical Support
Norm Lambert, President - Technical Support Director
info@epoxy.com
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
office@epoxy.com
352-489-1625 Fax line to all Departments
www.epoxy.com
24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Copyright © 1994-2007 EPOXY.COM a
division of Epoxy Systems, Inc. -
Florida and Vermont. All rights reserved.
Unless
other wise agreed upon in writing, buyer is responsible for the cost of
shipping.
This
information is presented in good faith to assist in determining whether this
product is suitable for application. No warranty or representation, however, is
intended or made, nor is protection from any law or patent to be inferred, and
all patent rights reserved.
Epoxy
Systems™ Product Company ("ESI") warrants its products (when properly stored)
for the period of time as follows: Epoxies, Product #315, Product #315BC, and
Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2)
months and Polyurethanes Four (4) months; Power Tools and Equipment 90
days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all
other resins (not specifically mentioned above) 30 days; hand tools (non-power
tools) 30 days. ESI warrants that its products will be free of
manufacturing defects and will be in conformity with published specifications
when handled, stored, mixed and applied in accordance with recommendations of
ESI. If any product fails to meet this warranty, the liability of ESI will be
limited to replacement of any non-conforming material if notice of such
non-conformity is given to ESI within the warranty period for the material (as
indicated above), or within 1 year of the delivery of materials (whichever is
sooner). ESI may in its discretion refund the price received by ESI in lieu of
replacing the material. No customer, distributor, or representative of ESI is
authorized to change or modify the published specifications of this warranty in
any way. No one is authorized to make oral warranties on behalf of ESI. In order
to obtain replacement or refund the customer must provide written notice
containing full details of the non-conformity. ESI reserves the right to inspect
the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED
WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS
FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY
UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE
PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY,
WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All
quotes and sales subject to availability.
Many of
our products are made on an individual order basis. Unless
authorized in writing by Epoxy Systems, Inc. in writing before the material is
made, there are no returns on items purchased from us, once the order has been
processed, and the material made. In the event of authorized returns a
restocking charge will be charged in the amount of 30% of the value of the
material returned or $150 whichever is greater. No returns on non-list
priced items. All Returns are for merchandise (store) credit only, no cash
or credit card credits. In the event of a return, buyer is responsible for
the cost of shipping and handling in both directions.
[Technical
Data Sheets in Adobe Acrobat Format][MSDSs
in Adobe Acrobat Format][Online-
Ordering Authorization Form]
Secure Login